0.4C-铬镍钼硅钢多冲疲劳裂纹起始寿命估算

 本文采用局部应力一应变法,结合Coffin公式,忽略弹性应变。考虑应变速率的影响,导出了在给定的试验条件下,根据材料的拉伸性能估算其多冲疲劳裂纹起始寿命的表达式,经试验结果验证表明,对不同冲击能量,不同热处理状态以及不同缺口形状的多冲试样,估算式均具有较高的准确性。     

基于Euler／N—S方程的跨音速非线性静气动弹性问题研究

在C-H网格的基础上,采用Jameson的中心差分有限体积法求解Euler/N-S方程,采用结构影响系数法计算结构的弹性变形,用三角元面积加权法和常体积转换法(CVT)实现流固耦合,计算了弹性后掠机翼在跨音速状态的静气动弹性问题     

基于约简遗传规划的线参数模型及在航空发动机起动建模中的应用

提出了一种新的约简遗传规划(PGP)算法和一种新的基于约简遗传规划的航空发动机起动动态线参数模型.这种模型采用遗传规划产生航空发动机起动模型的输入输出非线性模型集,并以二叉树结构表征函数项,运用正交最小二乘算法(OLS)估计二叉树分支(基本函数项)对于模型精度的贡献并去除复杂、冗余的函数项,从而加快遗传规划的收敛速度,最后通过GP进化可获得简单、可靠、准确的线参数非线性模型.发动机起动过程试车数据建模和与支持向量机的比较证明,这种方法可以产生适用性好、解析性强的线参数非线性模型,产生的模型可获得与支持向量机相当甚至更优的结果.     

Thermal Fatigue Behavior of Ni_3Al Based Superalloy IC6E

The thermal fatigue behavior of Ni3Al based superalloy IC6E during the cycles between 900 ℃/1 000 ℃ and the room tempera-ture was investigated. The experimental results indicate that the primary and secondary thermal fatigue cracks initiate inside or round the borides and then spread away along grain boundaries and/or in interdendritic areas. The fracture of borides and their separation from the matrix at interfaces are mainly responsible for the crack initiation and its spreading. At temperatures higher than 1 000 ℃, the grain boundary oxidation combined with cyclic stresses accelerates the crack growth.     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

Effects of the Fabrication Processes of NC-Si:H Films on Their Mechanical Properties

Studies of nanoindentation were performed on nc-Si:H films to evaluate the effects of the fabrication processes on their mechani-cal properties. It is observed that with the decrease of the SiH4 contents, the grain size of the films increases gradually, and as does the crystalline volume fraction. The smaller the grains become, the more homogeneous the films, and the more even the hardness as well as the modulus will be. The hardness and the modulus will increase with the substrate’s temperature rising. The hardness and the modulus of the nc-Si:H films on the Si substrate prove to be higher than those on the glass substrate given the same technology parameters. How-ever, the films on the glass substrate appear to be more homogeneous.     

轮盘应变疲劳寿命可靠性分析方法

为较准确评估应变疲劳寿命可靠性，通过引入两个相关随机变量对Coffin-Manson公式随机化，发展了一种轮盘应变疲劳寿命可靠性分析概率模型。对线性回归残差重新定义，使得到的回归参数不随坐标系的选取发生变化。采用响应面法和蒙特卡洛模拟相结合的方法获得轮盘危险点应变幅的分布，最后通过多次解非线性方程数值模拟得到轮盘危险点应变疲劳寿命分布及其可靠寿命。     

飞机铝梁接头耳片与钢衬套过盈配合对飞机寿命的影响

初步探讨了飞机机翼翼梁接头高强度铝耳片与钢衬套过盈配合在应力腐蚀与干涉连接综合作用下 ,对耳片疲劳寿命的影响及影响程度 ,并提出了结构设计时应遵循的几项原则。     

两种中温固化胶粘剂的剪切疲劳和蠕变性能研究

研究了SY 2 4B胶膜和SY H2糊状胶粘剂的剪切疲劳和蠕变性能。SY 2 4B胶膜和SY H2糊状胶粘剂同为中温固化的结构胶粘剂 ,SY 2 4B胶膜采用橡胶增韧 ,SY H2糊状胶粘剂采用热塑性树脂增韧。SY 2 4B胶膜虽然具有优异的韧性 ,但SY H2糊状胶粘剂的剪切疲劳和蠕变性能优于SY 2 4B胶膜 ,这与增韧剂种类与胶层厚度有一定关系。温度、应力和时间也是影响蠕变量的重要因素     

直升机主桨毂疲劳试验技术研究

直升机旋翼系统主桨毂是直升机关键部件，在地面运转及首飞前必须进行疲劳试验，根据试验结果确定初步疲劳寿命。本文以某型号直升机旋翼系统主桨毂疲劳试验为例，总结出多点协调加载试验台的设计方法及试验调试方法，并按照试验台的组成，从控制系统、泵站、伺服动作器、测量系统及试验台体等方面，详细阐述了设计内容及其工程效果。